Canopus Support Statement According to our product planning roadmap, the following hardware platforms will be supported by the next major release of EDIUS in Windows XP 32-bit editions, Windows Vista 32-bit editions and Windows Vista 64-bit editions: • IEEE 1394 (Generic OHCI) • ACEDVio • EDIUS NX Series • EDIUS SP Series • EDIUS SD/HDLE/HD Series (RX-E1) Windows Vista compatible 32-bit and 64-bit hardware drivers for the EDIUS NX series, EDIUS SP series and EDIUS SD/HDLE/HD series will be available with this next EDIUS release. OHCI and ACEDVio will continue to use the native OS drivers. At this time, we are still determining if it will be feasible to provide support for Windows XP 64-bit editions on the above hardware products. The following hardware platforms will not be supported in Windows Vista, and will remain supported up to EDIUS v4.x, under Windows XP 32-bit editions only: • DVRaptor RT2 Series • DVStorm Series • DVRex RT Series* • DVStorm XA Series (China only) • EDIUS DVX Series (Europe only) *DVRex RT Series is unofficially supported in EDIUS v4.00 to v4.24 – it is not supported at all in EDIUS v4.5 and later. We hope this clarifies our position with regards to EDIUS compatibility with the Windows Vista operating system. We welcome further discussion on anything that is unclear concerning our Windows Vista support roadmap for EDIUS, right here on the forums. Direct3D Statement With the storm you can not use 3d 9.

That is because of the way the storm works. The new overlay is available in ohci/sp/nx/sd/hd I think the op will have better luck if it is an overlay issue to use the ini edit. Overlay Recommendations When screen overlay does not show correctly with certain graphics cards If your screen overlay does not show correctly with PCI Express graphics cards), please add the below lines in the Canopus.ini file located in the C: WINDOWS folder. [DVStorm-RT.stmcore.conf] OverlayMethod=1 When the overlay does not show correctly when using certain graphics cards, you may also try adding the below lines in the Canopus.ini file located in the C: Windows folder. [DVStorm-RT.stmdd] OverlayUpdateMethod=1 If the above setting still does not fix the issue, please try changing the settings as below: [DVStorm-RT.stmdd] OverlayUpdateMethod=0 OHCI Recommendations As posted earlier, this is how I solved that exact problem with the DVX card which is a variant of the DVStorm.

EDIUS NX for HDV Expansion. Edius Nx Pci-X Driver. Compatible with Windows 10, 8.1, Windows 8. Canopus EDIUS NX. Canopus EDIUS Pro 4.5, Drivers.

[DVX-E1.dvxcore] PCIConfigChange=2 Have you looked at your CANOPUS.INI file to see if there is a similar section to this one? Call Of Duty 4 Promod 204 Download Games. [DVX-E1.dvxcore] It could be called [something-else.dvxcore]. If the section does not exist, then you can work out what the “something else” is from the other section headings and then try creating a similar entry to that above. For example, it might be [DVStorm2.dvxcore] And if “PCIConfigChange=2” does not work you can also try PCIConfigChange=1 and PCIConfigChange=3.

This is a known issue and you will see it documented on the Canopus hardware compatibility list webpage – although not every motherboard which is affected is listed there. Edius 5 Compatibility Install Edius 5 Install Edius 4.6 (with DVStorm drivers) Open 4.6 and create your preferred DVStorm setting, close 4.6 Open Edius 5 The Storm setting is now active Place a clip on the timeline Voila!! I have the following system. ASUS P5E64WS EVOLUTION CPU.

CORE 2 QUAD CORE Q9550 2.83 GRAFICS. ASUS EAH4870/HTDI DDR5 512MB PCI-E RAM. CORSAIR XMS3 DHX DDR3 4GB (2X2GB) PC3-12800 (1600MHZ) and two VELOCIRAPTOR WD 150GB as RAID0(stripe) and also the DVSTORM2 PRO.

I have two questions for you. When i try to capture a video from dvstorm2 pro with Premiere pro 1.5 or Edius 4,6 the picture stay still (freeze) on my monitor. I made all this above and works but the quality of video is very low and some pixels. How can i make capture-eding-video out in real time with Edius 5 from DVSTORM2 PRO? From motherbords IEEE 1394a there is very good quality video capture but i can not make an export of my video to DVD recorder.

(there is not a real time proview). Thank you for your reply congragulations for your Canopus Support Statement. Hi: Allow me to say upfront, I am a novice.

Hp Dc5750 Drivers Windows 7 32bit. Actually, novice is a kind word. I know nothing about video editing. However, I do have a predicament. I have a Canopus DVStorm2 Pro Card. It was previously on a a system that ran on an Intel P4 3.2Ghz, MSI 965PE Platinum, with an ATI AGP Video Card on Windows XP 32-Bit Pro. Worked perfectly. Now, I have upgraded to a system that is Intel Q9650 2.83Ghz on a Gigabyte P45-DQ6 Rev.

1.0 with a Palit 9600GT Sonic running on Vista 32-Bit Home Premium. I am having (from what I understand here) overlay problems. Could you please help me fix my problems. What should I do?

Please understand that I am very much new to technical language. I am looking for the ‘Idiot’s Version’ here. I am very much grateful for your help. Thank you so much in advance.